Ask AI
Skip to main content

Run an Osmosis node

The Osmosis Full Node will act as the source for the KYVE protocol validator and is required. You can either run the Osmosis node on the same machine with the KYVE protocol together (recommended) or on a seperate machine.

danger

Due to very specific requirements, an additional validation layer, accessibility as well as to prevent slashes, it is strongly recommended to run an independent data source node. API providers should be avoided and have already led to critical problems in the past.

Install Osmosis full node​

The Osmosis binary with the version v3.1.0 has to be installed. There are two ways to install and run the binary:

You can follow the official installation instructions here or download the binary directly from here.

danger

If you are building from source please use the specified go version in the go.mod file, else there is the danger of receiving vote slashes.

For osmosisd v3.1.0 it is go15

You can verify the successful installation with

./osmosisd version
3.1.0

After the successful installation, you need to set up the osmosisd config. First choose a moniker and initialize everything:

./osmosisd init <your-moniker> --chain-id osmosis-1

To download and setup the genesis file execute the following command:

wget -O ~/.osmosisd/config/genesis.json https://github.com/osmosis-labs/networks/raw/main/osmosis-1/genesis.json

Peers can be added via this addrbook which can be retrieved here:

wget https://dl2.quicksync.io/json/addrbook.osmosis.json
mv addrbook.osmosis.json ~/.osmosisd/config/addrbook.json
chmod 666 ~/.osmosisd/config/addrbook.json

TIP: You can also add persistent_peers from Polkachu to ensure that you will actually find peers where you can sync with the network: https://polkachu.com/live_peers/osmosis

Configuration​

Due to the size of the block_results response, it is required to set the following in your ~/.osmosisd/config/config.toml:

timeout_broadcast_tx_commit = "120s"

For efficient pruning, the following settings are recommended to decrease the disk usage:

~/.osmosisd/config/config.toml

[tx_index]

indexer = "null"

~/.osmosisd/config/app.toml

pruning = "everything"

index-events = [""]

Finally, the node can be started:

./osmosisd start --x-crisis-skip-assert-invariants
caution

ATTENTION: To be able to perform upgrades automatically, it is recommended to use the cosmovisor. How to set it up can be found here.

To start the Osmosis node with the cosmovisor, run:

cosmovisor run start --x-crisis-skip-assert-invariants
warning

WARNING: Because Osmosis had 3 hard forks (off-chain software upgrades), it's strongly recommended to disable binary downloads with DAEMON_ALLOW_DOWNLOAD_BINARIES=false. More information about managing the hard forks can be found here

Verifying the completed node setup​

After the successful start of the node you have to sync blocks until the latest summary of the pool is reached. For example if the latest pool summary is 1,000,000 you can check if the node has synced the blocks until that height with:

curl http://localhost:26657/block?height=1000000

If it returns a valid block response you can continue with starting the actual KYVE protocol validator and start participating in the validation and archival process.

TIP: to save storage space you can start pruning blocks manually after they have been archived by the pool since after that they are not needed anymore.

Managing hard forks​

Osmosis had three software upgrades which were executed without submitting SoftwareUpgrade governance proposals. As a result, the cosmovisor does not recognize these necessary upgrades, which is why the node can no longer sync from a specific height. These hard forks occured at the following heights:

To prevent longer syncing breaks or other issues, it's recommended to use the cosmovisor with already downloaded binaries. After that, you need to move

  • the osmosisd v6 binary in the upgrades/v5/bin directory,
  • the osmosisd v8 binary in the upgrades/v7/bin directory and
  • the osmosisd v10 binary in the upgrades/v9/bin directory.